Simple Installation

1. Carefully remove paper back.
2. Starting at one end carefully press decal in to desired position, work out air pockets.
3. Carefully remove clear covering being careful not to tear the decal.

That simple to install.

General instructions

1. Clean the area where you will apply this decal
2. Measure to put on the right place, use tape to hold the top and make sure is ok.
3. Peel the back
4. Stick the decal even from side to side or top to bottom. do it even to avoid bubbles.
5. REMOVE transfer tape.

SURFACE PREPARATIONS

All surfaces must be thoroughly cleaned of wax, dirt and any old adhesive residue before applying your vinyl graphics to ensure proper adhesion, otherwise peeling or lifting may occur.

Please read the instructions below for specific material cleaning procedures.

Fiberglass Boats: Clean surface with acetone or our prefered cleaner -3M General Purpose Adhesive Remover (which comes in an aerosol spray can). After solvent has evaporated wipe down area with soapy water (a few drops of hand dishwashing liquid mixed with water in a spray bottle).

Plastics and Glass: Wipe surface clean with a window cleaner. Remove any tape or glue residue with a single edge razor blade or plastic scraper.

Painted Metals and Base Metals: Clean surfaces with a solvent such as Lacquer Thinner. Dry the surface with a lint free cloth before the solvent evaporates and re-clean with a soapy water solution before applying graphic.

Freshly painted surfaces should be dry for at least 72 hours prior to application of the vinyl graphics. Interior Painted Surfaces: Surfaces may be cleaned with any household cleaner or mild soap and water.

Temperature Requirements: The temperature of the room and the temperature of the intended surface should be between 45 and 80 degrees Fahrenheit for best results. Very high humidity (above 90 percent) may effect the application process.

APPLICATION

1. You will need masking tape, spray bottle, Joy or dish washing liquid, and a tape measure.
   
   
2. Using the masking tape to underline where you want to place the vinyl sign. If you have letters that drop below the line, remove tape in that area.
   
   
3. With you spray bottle, mix a solution of 20 drops of Joy, Ivory, etc in one pint of water. Carefully spray the soapy water on the area where you want to place the vinyl.
   
   
4. Place the Graphics face down and peel away the waxed paper backing. Then spray the solution on the back of the vinyl sign. Be sure the Graphics is adhering to the application tape (premask).
   
   
5. While the area is still very wet, place the Graphics in the selected position. The soapy water allows you to slide Graphics into place. Gently rub palm over Graphics. (The water has no bearing on the adhesion; it is only for positioning the Graphics and removing the air bubbles.)
   
   
6. Use the an squeegee ( credit card )to squeeze the water out from under the Graphics. Squeegee in all directions and repeat several times. This process removes air & water from under the Graphics.
   
   
7. Let the Graphics dry completely. The amount of time needed to dry depends on the temperature and the humidity. Estimated time: 80 degrees - 30 minutes, 70 degrees - 3 hours, 50 degrees - 4 to 6 hours. These are recommendations ONLY….the Graphics MUST dry prior to the next step. 60 - 70 - 80 degrees are recommended temperatures for post installation.
   
   
8. Slowly peel back the pre-mask translucent application tape; the Graphics will adhere to the boat. If the Graphics don't adhere to the boat, you didn't wait long enough for the water to dry behind the Graphics; repeat squeegee process. LET DRY.
   
   
9. Now check for any bubbles. If you find any, place a small piece of pre-mask tape over the area; squeeze to the closest edge. If you still have a small bubble you can pop it with a pin. Small bubbles will eventually disappear from the sun over time.
   

HELPFUL HINTS:
On a windy day, be very careful when you peel the vinyl graphics off the backing paper. The Vinyl graphics are very sticky; don't let it crease. Spray graphics over the sticky side as you peel off wax paper. Do not try to install on a windy day. Do not attempt installation in direct sunlight on a hot day (do it in the shadow or a closed area) If you need to remove old painted letters, use Easy-Off oven cleaner. Please test in an inconspicuous area before using. Please wear gloves and eye protection. If you have any other questions, please feel free to contact us. NEVER APPLY DIRECT HEAT (E.G. BUFFING WHEEL, HEAT GUN, BLOW DRYER)